Best Mining Solutions For Everyone, Get a Free Quote.
Sand washer is also called sand washing machine.
Application Range: Sand making plant, mine field, construction, transportation, chemical engineering, water conservancy and concrete batching plant.
Applied material: River sand and artificial sand.
Need A High Quality Mining Machine For Your Project?Contact With Us
You May Also Like
This guide applies to both front load and top load washers. We will list each part and or area to check on your washer regardless of brand or type. The first solution will be the most likely and the least likely at the bottom of the list
These repair and troubleshooting methods are for all washing machines including Admiral, Amana, Beko, Bosch, Electrolux, GE, Haier, Hotpoint, Kenmore, LG, Maytag, Samsung, Sharp, Siemens, Toshiba, Westinghouse, and Whirlpool
Assuming the TUB IS SPINNING but does not get the water out of your clothing…– Make sure the washer is programmed to the correct wash cycle, different cycles have different speeds!– Make sure the drain hose on the back of the washer is not clogged or bent.– Check that the drain hose on back of washer is positioned correctly in standpipe and is able to drain properly.– Check the drain pump debris filter or coin trap, objects may be blocking the water flow.– Check inside drain pump and all hoses connected to drain pump for foreign debris or small pieces of clothing.– Be sure the wash load of clothing is balanced, balance out the wash load if you see all clothing to one side.– Check washer belt to be sure it is not stretched out or damaged. (for most top loaders)– Check direct drive motor coupling system to be sure there is no visible damage. (for most front loaders)– Lid switch or door lock assembly may be damaged or bent and not making the electrical safety “connection”
FULL SUMMARY – DETAILED TROUBLESHOOTING – FIRST MOST LIKELY TO CAUSE WET CLOTHESIf the clothing in your washer is still soaking wet once your washing machine is finished washing, check the following:Assuming the TUB IS SPINNING but does not get the water out of your clothes
If the washer is not spin drying your clothing, check the drain hose on the very back of your washing machine. Make sure the drain hose is not bent therefore restricting water to drain out and leaving your clothing wet even after spin dry mode is complete. It is also a good idea to remove the hose from the drain pump and check the pump and drain hose for any blockages that may restrict water flow
If the drain hose on the back of your washer is too far down or not down far enough in the standpipe, this can cause an issue with proper draining and can cause the washer to not fully drain out the water and therefore your clothing will still be soaking wet after a wash cycle
If you are trying within the service hours and are still seeing this message, please try again or call our customer service line:
Spin speeds can vary by the cycle that is selected. Your washer is designed so that in certain cycles, such as delicate or handwash cycles, the spin speeds are slower. In these cycles, more water is retained in the load at the end of the cycle to keep delicate fabrics from shrinking and wrinkling. Select the appropriate cycle based on the fabric being washed.
Consider adding more items to help balance the load during spin. Select drain and spin cycle and restart the washer. Your washer is designed to detect an unbalanced load and automatically lower the spin speed. Unbalanced conditions are more likely to occur with a single, bulky item
Use only HE High Efficiency detergent. Using non-HE detergent or more than the manufacturer's recommended amount of detergent can cause excessive suds. The excess suds can cause the washer to run at a reduced spin speed, which will result in very wet loads
Make sure the drain hose is not kinked. Straighten the hose for adequate water flow. Remove any blockage from the drainpipe or utility sink. Use the U-shaped drain hose form on the drain hose, and secure the drain hose. See the Installation Instructions for details; find them by entering your model number in the Manual and Literature search below
The drainpipe (standpipe) height requirements are: 96" (244 cm) maximum and 30" (76.2 cm) minimum. Your washer will not be able to adequately pump the water out of the washer if the drainpipe (standpipe) exceeds 96" (244 cm). In this case, the water may flow back into the washer. See the Installation Instructions for details; find them by entering your model number in the Manual and Literature search below
Copyright © 2021 Facdori Machinery All rights reservedSitemap