Best Mining Solutions For Everyone, Get a Free Quote.

Zhengzhou, China

[email protected]

Blogs

  1. Home
  2. Crushing Plant
  3. interview question for instrument mechanician in mining industry

interview question for instrument mechanician in mining industry

Crushing Plant

Crushing Plant

The combination crusher is a new generation high efficiency crushing machine designed and researched by integrating the domestic and foreign crusher technology with the same kinds and optimizing the main technical parameters.
[email protected]
Sent Message Chat Online

We Provide You The Highest Quality Mining Machine That Meets Your Expectation.

Need A High Quality Mining Machine For Your Project?

Contact With Us

You May Also Like

top 36 mining interview questions with answers pdf

Slideshare uses cookies to improve functionality and performance, and to provide you with relevant advertising. If you continue browsing the site, you agree to the use of cookies on this website. See our Privacy Policy and User Agreement for details.

In this file, you can ref interview materials for mining such as, mining situational interview, mining behavioral interview, mining phone interview, mining interview thank you letter, mining interview tips …

field instrumentation interview questions and answer

The differential pressure measured has nonlinear relation with flow through the pipeline. Differential pressure developed by a venturi, orifice plate, pitot tube, or any other acceleration-based flow element is proportional to the square of the flow rate. The square root extractor is used to convert the measured differential pressure into the flow rate

The following steps are to be taken which calibrating: 1. Adjust zero of the Tx’r. 2. Static pressure test: Give equal pressure on both sides of the transmitter. Zero should not shift. If it is shifting carry out static alignment. 3. Vacuum test: Apply equal vacuum to both the sides. The zero should not shift. 4. Calibration Procedure: * Give 20 psi air or 24V DC supply to the transmitter

* Vent the L.P. side to atmosphere. * Connect the output of the Instrument to a standard test gauge or Multimeter and adjust zero. 5. Apply required pressure to high-pressure side of the transmitter and adjust the span. 6. Adjust zero again if necessary

Pressure gauge: This is the simplest method, for pressure gauge, is located at the zero level of the liquid in the vessel. Any rise in level causes an increase of pressure which can be measured by a gauge

field instrumentation interview questions and answer

Purge system: In this method, a pipeline is installed vertically with the level open and zero. The other end of the tube is connected to a regulated air supply and to a pressure gauge. To perform a level measurement, the air supply is adjusted so that the pressure is slightly higher than the pressure due to the height of the liquid. This is achieved by regulating the air pressure until bubbles are seen in the cabin leaving the open end of the pipe

Differential pressure meter: Connections are made at the vessel top and bottom and to the two columns of the D.P. meter. The top connection is made to the L.P. column of the transmitter and the bottom to H.P. column of the transmitter. The difference in pressure in the vessel is balanced out since it is fed to both the column of the meter. The difference in pressure deducted by the meter will be due only to the changing, level of the liquid

instrument technician interview questions & answers

In this post, you can reference some of the most common interview questions for a instrument technician interview along with appropriate answer samples. If you need more job interview materials, you can reference them at the end of this post

Try not to use an example where you created the pressure yourself, by waiting too long to start something, or by handling a task irresponsibly at the beginning. For example, working under pressure to meet a customer’s deadline could be a good example, but not if you had waited too long to start the project

“Pressure is actually a catalyst to my work. When there is an imperative deadline, I refocus my energy into my work which in fact, has helped me to produce some of my best works. (Give examples) I guess you can say I thrive under pressure.”

If you are being asked this question from your employer then you can explain your experience. Tell the employer what responsibilities you were performing during your job. You can tell what programs you developed and what modules you worked on. What were your achievements regarding different programs

instrument technician interview questions & answers

I have been working with computers since 2001. I also have a degree in network support/computer repair. I have built my last 3 computers, have work with Dell as an employee. So I have around 15 years experience working with computers

Employers look for applicants who are goal-oriented. Show a desire for continuous learning by listing hobbies non-work related. Regardless of what hobbies you choose to showcase, remember that the goal is to prove self-sufficiency, time management, and motivation

Recent Posts